10 Things We All Hate About Repair Car Keys

How to Repair Car Keys

The car keys are tiny and might not seem to be important, but they're essential for the proper operation of your vehicle. The cost of replacing an old or modern transponder car keys can be upwards to $200.

However, there are ways to repair your car keys at home for only a fraction of the cost. This article will address the most frequent car keys issues and their DIY fixes.

Dead Key Fob Battery

The remote key fobs that come with cars make it simpler than ever before to open the trunk, doors and the tailgate. The battery of the device is prone to dying. There are some tricks you can use to solve this issue quickly.

First, check if the car is in ignition mode. If so the battery of the key fob may be low, but not dead. To test this, press the button on the key fob straight up against the vehicle's ignition button. If this is successful, the battery is likely fine and only needs to be changed.

To replace the fob's battery, start by prying open the case with a screwdriver or watch-type tool. Don't apply too much force, as this may cause the fob's casing to split. If the fob doesn't seem to be coming open with ease, try placing your pry tool into several places on the outside of the case.

Open the electronic portion of your vehicle after you have removed the mechanical key. Install the new battery and then snap back the shell. If the key fob isn't working after this procedure, there could be a bigger problem with your car's remote start system that requires a professional diagnosis. If this is the case, a reputable mechanic should be able to assist you. If you require assistance with your car and you need help, you can call roadside assistance.

Broken Key Ring

There are a few things that you can do when your key fob does not work because the ring is broken. The first step is to see if your broken piece is still in the ignition. If it is, remove it without damaging the ignition lock or door lock. Contact a locksmith if are having trouble getting rid of the key. They have tools that are able to safely remove keys that are damaged from the ignition.

A broken car key can also be caused by corrosion on the plastic frame or circuit board. You can clean the circuit board by using a cotton swab and ruby alcohol. This will eliminate the corrosion and stop damage to the contact pads.

If your key isn't starting because of a broken ring, you may be able to repair it with a strong wire or nail to close the hole. Superglue can also be used to fix a broken ring. First, clean the broken ring with a damp towel and then apply a small amount superglue on each end of the wire or nail. Allow the pieces to dry, and then press them in place. These DIY solutions can look appealing, but they're only a stopgap measure. For long-term repairs, you'll want to get a professional locksmith. They have the tools and expertise to fix a broken car key quickly and effectively. They can replace the battery and reprogram your key fob in the event of need.

Click On this page  may break due to wear and tear. If this happens, it's time to purchase a new key. Luckily, this problem isn't as bad as it may appear at first. The main problem is that the blade snapped off the case.

Spraying lubricant into the keyhole is one way to fix the problem. Then you can use pliers, pins, or tweezers to grab the damaged key and pull it out. You can also use a magnet if the key is magnetic. Use a magnet to assist you remove the key, but take care to not damage the lock tumbler.

If you're unable to take the broken piece from the key, contact an expert locksmith immediately. They're equipped with special tools to safely extract keys without causing damage.

You can also try super glue to fix a broken key. Apply a small amount of glue to the edges of the break and press them together. Wait until the glue is dry before inserting the key into the lock. This method is not very reliable, and you might have to repeat it several times before it works. Super glue might not be able to hold the key together. This is more of a temporary fix than a permanent solution.

Broken Plastic Loop

If the loop of plastic on your key fob fails it could render the key ineffective. It's a fairly simple fix. You can use wire or a finishing nail to replace it. For each end of the nail or wire you need to drill two holes into the plastic loop. Cut the wire or nail to key width, and then place tiny drops of superglue into each hole. Then, press the wire or nail into the holes until it closes them and allow it to dry.

Another option is to get an alternative shell from a locksmith who sells them. They can transfer the programmable section of your key to the new shell, and then cut new blades for less than the cost.

This isn't the best solution, but will help you get back on the road once more if your key split in half. It's not easy to fix when the key blade is in the ignition, however. If you're not cautious you could use a hair clip or a needle to remove the damaged part from the ignition. Get a locksmith equipped with special tools to safely remove broken keys from ignitions. They can also make you new keys with the appropriate cuts for your vehicle's ignition and ensure it works properly when it is inserted into the lock.

Broken Master Key

If a key gets damaged inside the lock, you'll need to find it before it is completely destroyed. You can make use of lubricants, tweezers, and needle nose pliers to grab the fragments of a damaged key.

To begin, spray the interior of your lock with a lubricant such as WD-40 or graphite powder. You could also try the hacksaw blade method, which involves gently sliding the blade down along the side of the broken key, and connecting to a few of the 'teeth' - if you succeed in doing this, you should be able remove the broken key from the lock.

Many hardware stores carry a spiral key extraction tool. This tool has a thin rod that is flexible and has spiral threads that can be placed in the keyway, and later bent into the broken part of the key. Once it is firmly anchored to the serrations you can twist the bar into a circle and then pull it up against the broken section of the key.

It's worth trying to remove the master key that is broken before calling an expert locksmith. If you can't get the piece out, it's time to call the big guns and have a locksmith cut you a new key and reprogram it using the transponder of your car.